Solutions · MEP Solutions
Services support that survives the ceiling void
Beam clamps, threaded rod, channel support, cable containment, pipe fixings and plumbing systems, the support and distribution layer, drill-free where the structure allows.
The problem
MEP support is where programme is lost. Drilling into structure for every hanger is slow, damages post-tensioned slabs, and multiplies inspection points. Meanwhile the wrong plating on a rooftop plantroom hanger will bloom rust before handover.
How MST answers it
MST supplies drill-free beam clamp systems, threaded rod, channel support, cable containment and pipe fixings as a coordinated kit, sized to the load and specified to the right corrosion class for indoor, plantroom or rooftop service.
Product lines
What sits inside this solution
Browse the solution by family. Each line is supplied against the standard named on your specification, send the clause and we will confirm the grade and the certification route.
Support & fixing systems
- Beam Clamp-A & Girder Clamps
- Threaded Rod, Nuts & Washers
- Strut Channel & Channel Nuts
- Seismic & Sway Bracing
- Anchors & Post-Installed Fixings
Cable management
- Cable Trays & Ladders
- Cable Trunking & Wire Basket
- Cable Ties, Glands & Accessories
- Earthing & Bonding Components
Pipework & plumbing
- U-Bolts & Split Pipe Clamps
- Pipe Hangers & Rollers
- Drainage & Pressure Pipe Systems
- Valves, Strainers & Pumps
Product schedule
Representative supply range
Indicative of normal stock and made-to-order supply. Project-specific grades, lengths and coatings are confirmed against the approved submittal before order.
Beam Clamp-A (girder clamp, top-flange)
MSS SP-58 Type 20 / 21
- Material
- Malleable iron / forged carbon steel
- Size
- Flange 3 – 40 mm, M8 – M20 rod
- Finish
- Electro-zinc, HDG
Threaded Rod
DIN 976-1, Class 4.8 / 8.8
- Material
- Carbon steel
- Size
- M6 – M30 × 1 m / 2 m / 3 m
- Finish
- Electro-zinc, HDG, A2/A4 stainless
U-Bolt (round bend, with nuts)
MSS SP-69 Type 24
- Material
- Carbon steel / stainless
- Size
- ½ in. – 12 in. NB, M8 – M20 thread
- Finish
- Electro-zinc, HDG, A4 stainless
Strut Channel & Channel Nut
MSS SP-58 support channel
- Material
- Cold-formed carbon steel
- Size
- 41 × 21 / 41 × 41 mm, 1.5 – 2.5 mm
- Finish
- Pre-galvanized, HDG
Cable Tray & Ladder
IEC 61537 / NEMA VE 1
- Material
- Pre-galvanized or HDG steel
- Size
- 50 – 900 mm width, 1.0 – 2.0 mm
- Finish
- Pre-galv, HDG, epoxy coated
Split Pipe Clamp with Rubber Lining
MSS SP-58 Type 3 / 4
- Material
- Carbon steel with EPDM liner
- Size
- 15 – 300 mm OD
- Finish
- Electro-zinc, HDG
Drop-In & Wedge Anchor
ETA assessed / ICC-ES evaluated
- Material
- Carbon steel, A4 stainless
- Size
- M6 – M20
- Finish
- Zinc plated, HDG, stainless
Seismic Bracing Attachment
MSS SP-58 / bracing schedule
- Material
- Forged carbon steel
- Size
- M10 – M20 rod, 360° swivel
- Finish
- Electro-zinc, HDG
Sizes shown are the standard supply envelope; larger diameters and non-standard lengths are produced to order. All grades are supplied with EN 10204 3.1 inspection certification referenced to the heat number unless otherwise agreed.
Product profiles
The profile families in this basket.
Article codes, stocked sizes and stock lengths, as they appear in the catalogue a specifier orders from.
Support system profiles
Strut channel, brackets, clamps and threaded rod for suspending pipework, ductwork, cable tray and containment from slab or structure.
- Materials
- Pre galvanised, hot dip galvanised and stainless steel
Made to the project drawing rather than to a stock schedule. Send the detail and we will section it.
Sizes shown are the stocked increments, not the limit of what can be sectioned. Each family also has its own catalogue with the full dimensional drawings; ask for the ones relevant to your package.
Threaded rod, stress area and indicative hanger capacity
Tensile stress areas are geometric and fixed by ISO 898-1. Hanger capacities follow MSS SP-58 practice for ambient-temperature carbon steel rod and are indicative only. The governing value is always the project structural calculation.| Rod size | Tensile stress area | Indicative safe load | Typical service |
|---|---|---|---|
| M8 | 36.6 mm² | ≈ 3.4 kN | Small bore pipe, cable tray |
| M10 | 58.0 mm² | ≈ 5.4 kN | Ductwork, light pipework |
| M12 | 84.3 mm² | ≈ 7.9 kN | Chilled water risers |
| M16 | 157 mm² | ≈ 14.7 kN | Large bore, firefighting mains |
| M20 | 245 mm² | ≈ 22.9 kN | Plant skids, heavy headers |
| M24 | 353 mm² | ≈ 33.0 kN | Primary plant support |
Safe loads shown assume static ambient service with no seismic or thermal amplification. Apply the project's load factors, and reduce for elevated temperature and for rod exceeding the unbraced length in the bracing schedule.
Applications
Where this is used
- Chilled water, firefighting and process pipework hangers
- Ductwork and AHU / FCU suspension
- Cable tray, ladder and busbar support
- Rooftop plantroom and condenser skids
- Drill-free connection to steel beams and purlins
- Seismic and sway bracing to project bracing schedules
Environment & finish
Corrosion strategy, by site condition
The Kingdom is not one environment. The finish that lasts twenty years in Riyadh will fail inside a warranty period on the Gulf coast.
Conditioned interior
Electro-zinc plated to ISO 4042 (Fe/Zn 5–8 µm) is normally sufficient for ceiling voids, risers and conditioned plantrooms. Cost-efficient and readily available across the full size range.
Rooftop, external and wet plantrooms
Hot-dip galvanized to ASTM A153 or A4 / AISI 316 stainless. Riyadh and Eastern Province rooftops see surface temperatures well above ambient plus chloride-bearing dust, electro-zinc plating will not last the defects liability period there.
Governing standards
What this discipline is measured against
- MSS SP-58 / SP-69 pipe supports
- DIN 975 / DIN 976 threaded rod
- IEC 61537 cable tray systems
- ISO 898-1 Class 4.8 / 8.8
- ISO 4042 electroplated coatings
- ISO 3506 A2 / A4 stainless
- SBC 501 / 601 mechanical & electrical
Where a project specification calls out a standard not listed here, send the clause reference with your enquiry, the technical desk will confirm equivalence or source to the named standard directly.
How we source
Three corridors, one certification regime.
Where a line comes from changes its lead time, its certification route and its landed cost. We state the corridor openly rather than hiding it behind 'globally sourced', it is usually the first thing a procurement manager needs to know.
Europe, UK & USA
Germany · Italy · UK · USA
Western-spec lines where the consultant names an EN or ASTM source mill, and ETA-assessed anchors and facade systems.
Gulf & Kingdom
KSA · UAE
Local manufacture and stock for programme-critical lines, with the shortest lead time and full local content and Saudization credentials.
Asia & Türkiye
China · Taiwan · Malaysia · Türkiye
Volume manufacture on certified lines where the specification permits it, same certification regime, tested and documented to the same standard.
Other disciplines
Explore the rest of the range
Civil Solutions
Structural bolting, anchor bolt assemblies, rebar couplers and formwork accessories, with the waterproofing, tanking and thermal insulation around the concrete.
Construction Chemicals
Admixtures, non-shrink grouts, repair mortars, anchoring adhesives, sealants and industrial flooring, the chemistry that makes the mix work at 45 °C.
Sustainable Solutions
Flange bolting for refineries and gas plants, plus mounting structures, balance-of-system and earthing for utility-scale and rooftop solar.
Send us your specification
Send the bolting schedule or specification section. We return grade confirmation, finish recommendation, lead time and certification route.